Устройство плавного пуска Schneider Electric Altivar ATS480, 88A (ATS480D88Y) 

Производитель Schneider Electric Тип Плавный пуск Серия Altivar ATS480 Номинальное напряжение сети, В 208...690 - 15...10 % Номинальная частота сети, Гц 50/60 Количество фаз сети 3 Выходной ток нагрузки, А 88 Мощность нагрузки, кВт - Байпас нет Защиты привода Обрыв фазы Встроенная тепловая защита Тепловая защита Перегрузка по току Недогрузка Чрезмерное время запуска, блокировка ротора Обрыв фазы двигателя Обрыв фазы питающей сети Обрыв фазы питающей сети Тепловая защита Количество дискретных входов, шт 2 Количество дискретных выходов, шт 2NO Количество аналоговых входов, шт 4 Количество аналоговых выходов, шт 1 Физический интерфейс RS-485 Степень защиты, IP IP00 Рабочая температура, °C -15...+40 Температура хранения, °C -25...+70 Ширина, мм 190 Высота, мм 290 Глубина, мм 247

 

 

Dimensions Drawings

Dimensions

 

Front, Side and Rear View

Connections and Schema

Power Connections

 

(1) : Mains side

(2) : Motor side

1/L1, 3/L2, 5/L3 : Mains supply inputs

2/T1, 4/T2, 6/T3 : Outputs to motor

A2, B2, C2 : Soft starter bypass

 

Connection in line, with line contactor, no bypass, type 1 or 2 coordination, non - reversing, 2-wire or 3-wire control

 

(1) : Installation of additional fast-acting fuses to upgrade to type 2 coordination according to IEC 60947–4–2.

(2) : Take into account the electrical characteristics of the relays (Control Terminal Characteristics).

(3) : The transformer must supply 110...230 VAC +10% — 15%, 50/60Hz.

(4) : RUN and STOP Management (3-wire control).

(5) : RUN and STOP Management (2-wire control).

 

Connection in line, with line and bypass contactor, freewheel or controlled stop, type 1 or 2 coordination, non reversing, 2-wire or 3-wire

 

(1) : Installation of additional fast-acting fuses to upgrade to type 2 coordination according to IEC 60947–4–2.

(2) : Take into account the electrical characteristics of the relays (Control Terminal Characteristics).

(3) : The transformer must supply 110...230 VAC +10% – 15%, 50/60Hz.

(4) : Take into account the electrical characteristics of the relays, especially when connecting to high rating contactor (Control Terminal Characteristics).

(5) : RUN and STOP Management (3-wire control).

(6) : RUN and STOP Management (2-wire control).

(7) : PC or PLC control

 

Connection inside the delta, with line and bypass contactor, type 1 and 2 coordination, non reversing, 2 wire or 3 wire

 

(1) : Installation of additional fast-acting fuses to upgrade to type 2 coordination according to IEC 60947–4–2.

(2) : Take into account the electrical characteristics of the relays (Control Terminal Characteristics).

(3) : The transformer must supply 110...230 VAC +10% – 15%, 50/60Hz.

(4) : Take into account the electrical characteristics of the relays, especially when connecting to high rating contactor (Control Terminal Characteristics).

(5) : RUN and STOP Management (3-wire control).

(6) : RUN and STOP Management (2-wire control).

(7) : PC or PLC control

 

Control block wiring diagram

 

(1) : Control power supply 110-230 VAC

(2) : External supply 24 VDC

(3) : 2 Wires PTC/PT100

R1A, R1C, R3A, R3C : Sequence relay

R2A, R2C : End of start

STOP, RUN, DI3, DI4 : Digital inputs

AQ1 : Analogue output

PTC1/AI1, PTC2, PTC3 : PTC or PT100 connection

DQ1, DQ2, DQ+ : Digital outputs

Mounting and Clearance

Mounting Position